Speed Queen SF7000WE Manual de Instalação

Installation Instructionsfor Stacked Washer/DryersOriginal InstructionsKeep These Instructions for Future Reference.CAUTION: Read the instructions bef

Order of Installation StepsThe proper order of steps must be followed to ensure correct in-stallation. Refer to the list below when installing your un

FLW2297N_SVG1Figure 46. Insert two plugs included in accessories bag into rear shippingbolt holes.FLW2358N_SVGFigure 57. Replace front access pane

the cold faucet goes to the valve marked “C”. Refer to Figure Figure 6 .6. Then, using a pliers, screw approximately 1/4 turn.IMPORTANT: DO NOT cros

a. Insert the end of the beaded strap into the larger holefound on the end of the strap.b. Tighten to desired fit.c. Lock strap in place by pull

Gas Dryers - Connect Gas Supply PipeWARNINGTo reduce the risk of gas leaks, fire or explosion:• The dryer must be connected to the type of gasas shown

D233I_SVG234151. New Stainless Steel Flexible Connector – (Use designCSA certified connector) Use only if allowed by local co-des2. 1/8 in. NPT Pi

Heating elements are available for field installation in dryerswhich are to be connected to electrical service of different volt-age than that listed

D816I_SVGL1 L2 L1 L21516522348912131011761141. A typical 30-Amp Three-Wire Receptacle NEMA Type 10-30R2. 120 ± 12 V.A.C.3. 240 ± 12 V.A.C.4. I

3. Use a strain relief and insert end of power cord through powersupply hole.D696I_SVGFigure 144. Use the three screws from the accessories bag to

DRY2468N_SVG11. Earth/Ground ScrewFigure 184. Use a strain relief and insert end of power cord through powersupply hole.DRY2469N_SVG1. Strain Re

Connect Dryer Exhaust SystemWARNINGTo reduce the risk of fire and combustion gas accu-mulation the dryer MUST be exhausted to the out-doors.W604WARNI

• Exhausting dryer in hard-to-reach locations can be done byinstalling 521P3 Flexible Metal Vent Kit (available as option-al equipment at extra cost).

Position and Level the UnitWARNINGUnits elevated above floor level must be anchored tothat elevated surface, base or platform. The materialused to ele

SWD1029N_SVG4532611. Level2. Wood Block3. Rubber Foot4. Leveling Leg5. Locknut6. Unit BaseFigure 22 Wipe Out Inside of Washer and DryerDru

WARNINGTo reduce the risk of fire, electric shock, serious in-jury or death, all wiring and grounding MUST con-form with the latest edition of the Nat

WARNINGThis unit is equipped with a three-prong (earth/ground) plug for your protection against shock haz-ard and should be plugged directly into a pr

Standard 120 Volt, 60 Hertz 3-Wire Effective Earth/Ground CircuitDRY2022N_SVG768543211. L12. Earth/Ground3. Neutral Side4. Round Earth/Ground

Gas DryersIMPORTANT: This operation is to be conducted byqualified personnel only.1. To view the burner flame, remove the lower front panel of thedr

Installer ChecklistFast Track for Installing the Stacked Washer/Dryer1 Position Unit Near Installation Area. 7 Connect Dryer ExhaustSystem.SWD997N_SVG

WARNING WARNINGRisk of fire. Highly flammable material.W881Read all instructions before using unit.WARNINGFOR YOUR SAFETY, the information in this ma

The following information applies to the state of Massachusetts,USA.• This appliance can only be installed by a Massachusetts li-censed plumber or gas

Table of ContentsDimensions... 6Installation...

DimensionsElectric ModelsSWD1003N_SVGOQPNMLKJIHGFEDCBAA * 66.06 in. [1678 mm]B * 56.97 in. [1447 mm]C 23.5 in. [597 mm]D 8.375 in. [213 mm]E 24 in. [6

* With leveling legs turned into base.** For ADA compliance turn legs out from base 0.5 inches.NOTE: Exhaust openings are 4 inch [102 mm] metalducting

Q 27.73 in. [704 mm]R (with door closed) 1.5 in. [38 mm]S *13.1 in. [333 mm]* With leveling legs turned into base.** For ADA compliance turn legs out

Installation Before You Start ToolsFor most installations, the basic tools you will need are:SWD1021N_SVG11109843216751. Wrench2. 1/4 inch Driver3